Canada: rules and approvals
Radio and wireless devices sold in Canada need ISED certification against the Radio Standards Specifications, such as RSS-247 for Wi-Fi and Bluetooth and RSS-Gen for general requirements and labelling.
The IS-04Z1 is an Ex phone for people working inside classified areas at Canadian oil sands plants, gas plants, refineries and offshore platforms. If you are specifying a rugged mobile phone for Canada, this page covers the markings, the approvals and the current certification status of the IS-04Z1.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. The SAMS IS-04Z1 is the intrinsically safe smartphone covered here for Canada: pre-launch, designed for Zone 1 and Zone 21 (marking target Ex ib IIC T4), with certification in progress and no certificate issued.
Status: pre-launch. IECEx, ATEX, UKEX and NEC 500 certification is in progress and no certificate has been issued; launch is planned for Q4 2026. An operator's own vendor approval is a separate step. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Ingress protection | IP65 to IP68 sealing | IP68 design |
| Drop and shock | A stated drop height onto concrete | Specification on request |
| Explosion protection | A separate certificate and marking | In progress; not issued |
| Where it applies | Canada: Athabasca oil sands, Cold Lake and the Lakeland, Alberta Industrial Heartland | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Canada. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
Operators and classified areas drawn from the SAMS Canada market guide.
Radio and wireless devices sold in Canada need ISED certification against the Radio Standards Specifications, such as RSS-247 for Wi-Fi and Bluetooth and RSS-Gen for general requirements and labelling.
Fort McMurray averages minus 17.2 degrees Celsius in January, with a recorded low of minus 53.3 degrees, so batteries, touchscreens and enclosures need to work in deep cold.
Canada also accepts field certification for custom-made or low-volume equipment, evaluated at the installation site, which is similar to unit verification under the IECEx and ATEX systems.
Hazardous locations in Canada fall under Section 18 of the Canadian Electrical Code Part I, which uses the Zone system, while the older Class and Division rules are kept in Annex J for existing installations.
A rugged phone is built to survive water, dust, drops and rough handling, usually rated by an IP code and a drop specification. Ruggedness is an environmental property: it says nothing about whether a phone may be used where flammable gas or dust is present. That is decided by explosion-protection certification and marking.
The IS-04Z1 combines both: an IP68 sealed rugged build and a design for Zone 1 and Zone 21 (marking target Ex ib IIC T4). The explosion-protection certificates are in progress and none has been issued.
In Canada. Winter dominates the Canadian specification: cold mornings at Fort McMurray, wind on the Grand Banks and Saint John. IP68 sealing and a rugged build are designed for the weather, but the marked ambient range comes only when the certificate issues. IP68 is not explosion protection, and cold also cuts battery capacity.
A short checklist for anyone writing or reviewing the specification, with the IS-04Z1 status against each point.
No. Nothing can be bought or taken into a classified area today: certification is in progress and launch is planned for Q4 2026. What is available now is the datasheet, the written certification schedule and evaluation units for safe-area use.
SAMS has not published a price. Any figure you are offered for an uncertified Ex phone should be treated with caution; written indicative pricing is available for a defined quantity and site.
It is designed to IP68 sealing, with glove-friendly controls. Ruggedness is not explosion protection: that depends on the certificates, which are in progress.
The market guide for Canada covers Athabasca oil sands, Cold Lake and the Lakeland, Alberta Industrial Heartland, Montney and Duvernay, among others. Site-level pages are linked below.
Not exactly. Explosion proof is a broad everyday term; intrinsic safety is one protection concept, which limits energy so ignition cannot occur. Flameproof (Ex d) is a different concept that contains an explosion. The IS-04Z1 is intrinsically safe by design.
Hazardous-location electrical equipment in Canada is generally expected to carry certification from a Standards Council of Canada accredited body, and IECEx or ATEX certificates are not accepted as a substitute, although they can speed the evaluation. Confirm the required marking with the site operator and a Canadian certification body.
Fort McMurray averages about minus 17 degrees Celsius in January and has seen extremes below minus 50, so check the datasheet's operating and charging temperature range, battery behaviour in cold, and glove-friendly controls. Confirm any site cold-weather procedures with the operator before deployment.
Every battery gives up capacity in the cold, and the 4,000 mAh cell is sized for a normal shift, not extreme cold. Unless a certificate says otherwise, hazardous area equipment is assessed for minus 20 to plus 40 degrees Celsius, and the marked range will be published when the certificate issues. Check it first.
Other guides for Canada, other places in Canada, and the pages behind them.
Send the site, zone and gas group and roughly how many handsets. We reply by email with the datasheet and the certification schedule.
Name the site and the operator and we will send what is available before launch.