Canada: rules and approvals
Hazardous locations in Canada fall under Section 18 of the Canadian Electrical Code Part I, which uses the Zone system, while the older Class and Division rules are kept in Annex J for existing installations.
Canada · explosion proof
Explosion-Proof Smartphone in Canada
The IS-04Z1 is an Ex phone for people working inside classified areas at Canadian oil sands plants, gas plants, refineries and offshore platforms. This page explains what to look for in an explosion proof smartphone for Canada, and where the IS-04Z1 stands against that list today.
Pre-launch · certification in progress · Launching Q4 2026
Marking targetEx ib IIC T4Intrinsic safety, Zone 1 / 21 design target · certification in progress
AvailabilityQ4 2026via authorised distributors
Search topicexplosion proof
DeviceSmartphone
RouteSpecification
WhereCanada
Short answer. The SAMS IS-04Z1 is the intrinsically safe smartphone covered here for Canada: pre-launch, designed for Zone 1 and Zone 21 (marking target Ex ib IIC T4), with certification in progress and no certificate issued.
Where things stand: the IS-04Z1 has not launched, and none of its four certification routes has produced a certificate yet. Operator approval runs on its own timeline. Certification status. Place facts reviewed October 2026.
At a glance · explosion proof
Checklist: explosion proof smartphone for Canada
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Protection concept | Flameproof (Ex d) or intrinsic safety (Ex i) | Intrinsic safety, level ib |
| Zone suitability | Zone 1 gas and Zone 21 dust | Design target for Zone 1 and 21 |
| Certificate | Number, issuing body and schedule of conditions | In progress; not issued |
| Where it applies | Canada: Athabasca oil sands, Cold Lake and the Lakeland, Alberta Industrial Heartland | Classified by the site operator |
Product · Canada
The product behind this search: the SAMS IS-04Z1.
SAMS IS-04Z1
An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Canada. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
- IP68 sealed
- 4,000 mAh battery
- 50 MP camera
- Android 16
- Zone 1 / Zone 21 design target
The market · Canada
Where this applies in Canada
The classified areas, operators and sites below are the ones covered in the SAMS Canada market guide.
Operators, EPCs and contractors
- Suncor Energy
- Base Plant, Fort Hills, Sarnia and Edmonton refining
- Cenovus Energy
- Foster Creek, Christina Lake, Lloydminster, offshore Atlantic
- Imperial Oil
- Kearl and Cold Lake, Strathcona and Sarnia refineries
- Canadian Natural Resources
- Horizon and Albian mining, Jackfish and Primrose thermal
- Syncrude
- Mildred Lake mining and upgrading, operated by Suncor
- Shell Canada
- Scotford upgrader, refinery and chemicals in the Heartland
Industrial areas and sites
- Athabasca oil sands
- Fort McMurray mines, upgraders and in situ plants
- Cold Lake and the Lakeland
- Thermal in situ pads and steam generation
- Alberta Industrial Heartland
- Fort Saskatchewan, Scotford and Redwater refining and chemicals
- Montney and Duvernay
- Gas plants around Grande Prairie and Fort St John
- Sarnia Chemical Valley
- Three refineries and dozens of chemical plants
- Kitimat and the north coast
- LNG Canada trains and jetty, Cedar LNG building
Field notes · Canada
More about Canada that matters for portable equipment
Canada: industry on the ground
The Athabasca oil sands in Alberta hold bitumen so viscous that it will not flow unless heated or diluted with lighter hydrocarbons such as condensate, so diluent and heating systems feature heavily at sites.
Canada: rules and approvals
Electrical products for hazardous locations must be certified by a body accredited by the Standards Council of Canada, and IECEx or ATEX certificates are not accepted in place of that certification.
Canada: background
The Great Canadian Oil Sands plant, now part of Suncor, opened in 1967, and Fort McMurray's growth took off as further oil sands plants followed after the 1970s energy crises.
The term · explosion proof
What “explosion proof” means for a smartphone
“Explosion proof” is the phrase most buyers use for equipment that may be taken into a classified hazardous area. Strictly, it covers several protection concepts: a flameproof enclosure (Ex d) contains an internal explosion, while intrinsic safety (Ex i) limits electrical energy so that an ignition cannot start. Phones are normally intrinsically safe, because a flameproof handset would be too heavy to carry all shift.
The IS-04Z1 uses intrinsic safety, with a marking target of Ex ib IIC T4, and is designed for Zone 1 and Zone 21. It is pre-launch, certification is in progress and no certificate has been issued.
In Canada. Explosion proof is the everyday phrase, but in oil sands upgraders or Sarnia plants the real choice is the protection concept per area. Flameproof Ex d suits fixed equipment; the IS-04Z1 uses intrinsic safety so a handheld can enter Zone 1 or Class I Division 1 areas live. The operator classifies each area, not SAMS.
The route · specification
Specifying an explosion proof smartphone for Canada
A short checklist for anyone writing or reviewing the specification, with the IS-04Z1 status against each point.
Check on the paper
- Marking
- Equipment group, category, protection concept, gas group and temperature class, matched to the area drawing.
- Certificate and schedule
- A certificate number, issuing body and the schedule of conditions, not a brochure claim.
- Standards edition
- The IEC 60079 or national standard edition the certificate was issued against.
Check for the IS-04Z1
- Marking target
- II 2 G Ex ib IIC T4: a target, not yet a certificate.
- Certificate status
- IECEx, ATEX, UKEX and NEC 500 in progress; none issued.
- Operator approval
- Separate from the certificate and handled with the site operator.
Questions · Canada
Frequently asked questions
Can we buy an explosion proof smartphone in Canada today?
Not today. Until the certificates are issued the IS-04Z1 stays out of classified areas, and until launch there is nothing to purchase. You can ask for the datasheet and the certification schedule, or book a safe-area evaluation unit.
What does an explosion proof smartphone in Canada cost?
No price is published. While certification is in progress there is no list price and no committed lead time, and a supplier quoting a firm figure for an uncertified Ex handset is promising something it cannot stand behind. Indicative pre-launch pricing is issued in writing against a stated quantity and site.
Is the IS-04Z1 explosion proof or intrinsically safe?
It is intrinsically safe (marking target Ex ib IIC T4), which is the usual way to make a phone for hazardous areas. It is not a flameproof (Ex d) design, and certification is still in progress.
Which sites in Canada does this cover?
The market guide for Canada covers Athabasca oil sands, Cold Lake and the Lakeland, Alberta Industrial Heartland, Montney and Duvernay, among others. Site-level pages are linked below.
Is intrinsically safe the same as explosion proof?
Not exactly. Explosion proof is a broad everyday term; intrinsic safety is one protection concept, which limits energy so ignition cannot occur. Flameproof (Ex d) is a different concept that contains an explosion. The IS-04Z1 is intrinsically safe by design.
What radio approval does a smartphone need in Canada?
Devices with Wi-Fi, Bluetooth or cellular radios generally need ISED certification and must meet the applicable Radio Standards Specifications, along with interference limits such as ICES-003. A certification body recognised by ISED can issue it. Confirm the exact requirements for your device with ISED or an accredited body.
Do Canadian sites use Zones or Divisions?
The Canadian Electrical Code now uses Zones in Section 18, while Class and Division rules remain in Annex J for existing installations, so older plants may still be classified by Division. Check the classification drawing for the area and make sure the device marking matches the system used there.
Does the phone carry both Zone and Division markings?
The marking target is II 2 G Ex ib IIC T4, with Class I Division 1 pursued on the same intrinsic safety basis. Nothing has been issued: certification is in progress. Canadian Section 18 classifies by Zone while Annex J18 keeps Division. Check which system your site's drawings use before anything is specified.
Related guides
Keep exploring
Related guides for Canada and for Canada.
Rugged Mobile Phone Supplier in CanadaSame place, different guide
NEC 500 Class I Division 1 Mobile Phone in CanadaSame place, different guide
IECEx Mobile Phone Supplier in CanadaSame place, different guide
Intrinsically Safe Mobile Phone in CanadaSame place, different guide
ATEX and IECEx Mobile Phone Distributor in CanadaSame place, different guide
Hazardous Area Mobile Phone in CanadaSame place, different guide
Canada market guideCertification route and regulators
All guides for CanadaEvery route we cover
Certification statusWhat is in progress
Enquiry · Canada
Ask about the IS-04Z1 for Canada
Share the site details and quantity. You will get the datasheet and the certification schedule back by email; pricing is indicative only until launch.
Enquiry · Canada
Launching Q4 2026
Planning for Canada?
Name the site and the operator and we will send what is available before launch.