Site access
Large works run their own contractor induction and permit-to-work systems, so access to classified areas is arranged through each operator.
Dalarna University was founded in 1977 as a joint college for Falun and Borlänge, and the town hosts the head office of the Swedish Transport Administration, Trafikverket. Steel and paper processing involve fuel gas, chemicals and fine dust, so Zone 1 and Zone 21 classification can apply in plant areas. This page explains what to look for in an Ex-proof smartphone for Borlänge, and where the IS-04Z1 stands against that list today.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. The SAMS IS-04Z1 is the intrinsically safe smartphone covered here for Borlänge: pre-launch, designed for Zone 1 and Zone 21 (marking target Ex ib IIC T4), with certification in progress and no certificate issued.
Status: pre-launch. IECEx, ATEX, UKEX and NEC 500 certification is in progress and no certificate has been issued; launch is planned for Q4 2026. An operator's own vendor approval is a separate step. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Ex marking | Group, category, protection concept, gas group, temperature class | II 2 G Ex ib IIC T4 (target) |
| Gas group | IIA, IIB or IIC matched to the area drawing | IIC (target) |
| Temperature class | T-class below the ignition temperature of the gas | T4, 135 °C (target) |
| Where it applies | Borlänge: Fuel and process gas systems, Chemical and oil storage, Dust-generating process areas (Zone 21) | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Borlänge. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
A short profile of the site and the kinds of classified area that matter for portable equipment.
Large works run their own contractor induction and permit-to-work systems, so access to classified areas is arranged through each operator.
Humid continental climate with cold winters (January averages about -1 degrees C), so outdoor rounds in winter call for cold-tolerant batteries and gloved operation.
SSAB describes its Borlänge works, established in 1878, as its largest strip rolling system, making hot-rolled and cold-rolled high-strength steel for automotive, heavy-duty transport, lifting and container uses, with around 1,700 employees.
The four blast furnaces and two Kaldo converters at Domnarvet were shut down in 1981, and the site since then has developed around its hot strip rolling mill.
SSAB's industrial area lies in downtown Borlänge, the Dal river flows through the site, and the works contain around 30 km of railroad track.
Borlänge Central is a railway junction for routes toward Falun, Mora and Ludvika and links to Gävle and Stockholm, and Dala Airport lies 8 km south-east, with Arlanda 214 km away.
“Ex-proof” is shorthand for equipment carrying an explosion-protection marking (the Ex mark) that matches the area it enters. The marking states the protection concept, gas or dust group and temperature class, and it must be backed by a certificate issued by a recognised body, so a phone described as Ex-proof should come with a certificate number you can check.
The IS-04Z1 is designed to carry the marking II 2 G Ex ib IIC T4. That is a target: certification is in progress, no certificate has been issued, and SAMS will publish the certificate numbers when they exist.
In Borlänge. A marking check around Borlänge would match the equipment marking to the zone given on the operator's classification drawings. Gas-side areas such as fuel and process gas systems may be Zone 1, while dust-generating process areas may be Zone 21. The IS-04Z1 target marking is II 2 G Ex ib IIC T4, which addresses gas only.
A short checklist for anyone writing or reviewing the specification, with the IS-04Z1 status against each point.
Not today. Until the certificates are issued the IS-04Z1 stays out of classified areas, and until launch there is nothing to purchase. You can ask for the datasheet and the certification schedule, or book a safe-area evaluation unit.
There is no list price yet. SAMS gives indicative pre-launch pricing in writing, against a stated quantity and site, and does not commit to a lead time before certification completes.
The marking target is II 2 G Ex ib IIC T4. It becomes a marking only when the certificate is issued; until then it is a design target.
Likely candidates are fuel and process gas systems, chemical and oil storage, dust-generating process areas (zone 21). Which areas are classified, and to what zone, is set by the site operator's own area classification drawings.
Not exactly. Explosion proof is a broad everyday term; intrinsic safety is one protection concept, which limits energy so ignition cannot occur. Flameproof (Ex d) is a different concept that contains an explosion. The IS-04Z1 is intrinsically safe by design.
Inland Dalarna can be cold in winter, so batteries and touchscreens may perform less well outdoors. Typically users keep spare batteries warm and check the device's rated temperature range against site conditions, while mills and steelworks may require protective cases.
Mills typically have combustible dust from wood and fibre, flammable gases in energy and chemical recovery areas, and solvent stores. Each site classifies its own areas, so ask the mill's safety team for zone drawings and whether handheld devices are permitted.
Large works here run their own contractor induction and permit-to-work systems, so access to classified areas is arranged through each operator. A phone would normally be listed and approved as part of that process. Ask the operator's HSE or procurement team what device evidence it requires.
Related guides for Borlänge and for Sweden.
Send the site, zone and gas group and roughly how many handsets. We reply by email with the datasheet and the certification schedule.
Tell us the zone, gas group and operator. We will send the datasheet and the certification schedule.