Denmark: logistics and access
Port Esbjerg calls itself the world's largest base port for offshore wind activities and says it has been involved in shipping components to more than 65 offshore wind projects.
The IS-04Z1 is an explosion proof mobile phone designed for Zone 1 and Zone 21, from a wet deck 225 km west of Esbjerg to a fermentation building at Kalundborg and a biogas upgrading skid on Lolland. Denmark imports about 12% of its energy but is also an exporter, and its electricity grid is connected by transmission lines to other European countries. Distribution partners for Denmark are being identified ahead of the Q4 2026 launch of the IS-04Z1.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. Denmark has no appointed SAMS distributor yet: the IS-04Z1 is pre-launch (certification in progress, no certificate issued, launch planned for Q4 2026), and distributor applications are open.
Current position: certification in progress, nothing issued, launch targeted for Q4 2026. An operator's own vendor approval is a separate step. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Marking | II 2 G Ex ib IIC T4 on the rating plate | Design target; not yet marked |
| EU-type examination certificate | Notified body number and certificate ID | In progress with TÜV; not issued |
| IECEx certificate of conformity | Number listed on the IECEx online register | In progress; not issued |
| Where it applies | Denmark: Fredericia, Kalundborg, Stigsnæs | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Denmark. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
The main operators, industrial areas and sites that the SAMS Denmark market guide covers.
Port Esbjerg calls itself the world's largest base port for offshore wind activities and says it has been involved in shipping components to more than 65 offshore wind projects.
Denmark has North Sea oil and gas but ranked only 57th among net crude exporters in 2023 after ranking 32nd in 2008, so offshore work is mature, with decommissioning and maintenance a larger share.
North Sea natural gas projects began in 1984 and North Sea production made Denmark self-sufficient in energy in 1997, which explains the established offshore supply chain on the west coast.
Manufacturers who apply the ATEX provisions and affix CE and Ex markings may sell equipment anywhere in the EU without further requirements for those risks, so Danish buyers can use EU-wide certificates.
ATEX is the European legal framework for equipment used in explosive atmospheres (Directive 2014/34/EU). IECEx is the international certification scheme built on the IEC 60079 standards. Buyers outside Europe often ask for both: an IECEx certificate is the technical evidence most national regimes build on, while ATEX is the legal route into the European market.
For the IS-04Z1 both routes are in progress with TÜV in Germany and neither certificate has been issued. The marking target is II 2 G Ex ib IIC T4: equipment Group II (surface industry), Category 2 (Zone 1 gas), protection concept ib (intrinsic safety), gas group IIC and temperature class T4.
In Denmark. Denmark is inside the EU, so ATEX is the product-side requirement and nothing national follows it. A reviewer would ask for the notified body certificate and CE marking, with an IECEx route helping offshore groups such as TotalEnergies EP Danmark and BlueNord, and contractors like Semco Maritime, who work across borders. Certification is in progress.
A distributor for Denmark would carry the IS-04Z1 after certification completes; the Q4 2026 launch is the planning date and no appointment has been made. SAMS reviews applicants one by one and prefers companies with their own Ex-competent technical and service staff, since certified devices must not be repaired outside approved channels.
Not today. Until the certificates are issued the IS-04Z1 stays out of classified areas, and until launch there is nothing to purchase. You can ask for the datasheet and the certification schedule, or book a safe-area evaluation unit.
SAMS has not published a price. Any figure you are offered for an uncertified Ex phone should be treated with caution; written indicative pricing is available for a defined quantity and site.
Not yet. Both routes are in progress with TÜV in Germany and no certificate has been issued. Any listing that says otherwise is wrong.
The market guide for Denmark covers Esbjerg, The Danish North Sea, Fredericia, Kalundborg, among others. Site-level pages are linked below.
Apply through the distributor page with your company details and the territory you cover. SAMS reviews applications company by company and has not yet granted a territory for Denmark.
Cold, wet and windy conditions affect battery life and touchscreen use with gloves, particularly offshore and at wind farms. Check the lowest rated ambient temperature on the certificate, the water ingress rating and whether touch input works with wet or gloved hands.
Typically the EU declaration of conformity, the certificate, the Ex marking details and instructions in the local language, which may be Danish or English depending on the operator. Request the site's equipment register template so supplier documents can be matched to it.
The classification of areas into zones comes from the emergency management agency under an executive order, while the employer's duty to assess explosion risk and hold an explosion protection document comes from the Danish Working Environment Authority. SAMS classifies nothing. Confirm the arrangement with the site operator for your plant.
Related guides for Denmark and for Denmark.
Tell us what you need to equip and where. The SAMS team answers by email with the datasheet and where each certification route stands.
Send the zone and gas group of your site and we will reply with the datasheet and schedule.