United States: rules and approvals
Full certification in the US includes quarterly factory inspections, while field certification offers an alternative for custom or low-volume equipment already at an installation.
The IS-04Z1 is built for people who work inside classified locations at American refineries, gas plants, terminals and wellsites, and for the HSE and IT teams who decide what goes through the gate. This page explains what to look for in an intrinsically safe smartphone for United States, and where the IS-04Z1 stands against that list today.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. The SAMS IS-04Z1 is the intrinsically safe smartphone covered here for United States: pre-launch, designed for Zone 1 and Zone 21 (marking target Ex ib IIC T4), with certification in progress and no certificate issued.
For the record, no certificate exists for the IS-04Z1 today. The programme is under way ahead of a Q4 2026 launch. An operator's own vendor approval is a separate step. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Level of protection | ia, ib or ic matched to the zone | ib, for Zone 1 |
| Entity parameters | Uo, Io and Po within the device limits | Published with the certificate |
| Accessories | Chargers and cases certified with the device | Defined at certification |
| Where it applies | United States: Permian Basin, Houston Ship Channel, Beaumont and Port Arthur | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in United States. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
The classified areas, operators and sites below are the ones covered in the SAMS United States market guide.
Full certification in the US includes quarterly factory inspections, while field certification offers an alternative for custom or low-volume equipment already at an installation.
The National Electrical Code covers hazardous locations in Article 500 for the Class and Division system and in Articles 505 and 506 for the Zone system, as adopted by each state or authority.
The FCC regulates radio frequency devices between 9 kHz and 3000 GHz, and most radio-containing products must follow an equipment authorisation procedure before being marketed.
Zone-rated equipment in the US carries the AEx marking, for example Class I, Zone 0, AEx ia IIC T6, so a datasheet showing only ATEX or IECEx marks does not show US approval.
Intrinsic safety limits the electrical and thermal energy in a circuit so that neither a spark nor a hot surface can ignite a gas or dust atmosphere, even when a fault occurs. The ib level, used for Zone 1, tolerates one fault. It is the usual way to make a handheld device that a worker carries continuously through a hazardous area.
The IS-04Z1 is designed on this principle for Zone 1 and Zone 21 (marking target II 2 G Ex ib IIC T4). Intrinsic safety is a design basis, not a certificate: certification is in progress and none has been issued yet.
In United States. Intrinsic safety suits pumper routes and compressor stations where hours separate charging points, and the long rounds at Gulf Coast refineries. A handheld that limits ignition energy lets a worker record, photograph and communicate with one hand free, which matters with gloves, fixed ladders and permit paperwork.
A short checklist for anyone writing or reviewing the specification, with the IS-04Z1 status against each point.
No. Nothing can be bought or taken into a classified area today: certification is in progress and launch is planned for Q4 2026. What is available now is the datasheet, the written certification schedule and evaluation units for safe-area use.
There is no list price yet. SAMS gives indicative pre-launch pricing in writing, against a stated quantity and site, and does not commit to a lead time before certification completes.
The circuits are designed to limit energy so a spark or hot surface cannot ignite a gas or dust atmosphere, even with one fault (level ib, Zone 1). Certification of that design is in progress.
The market guide for United States covers Permian Basin, Houston Ship Channel, Beaumont and Port Arthur, Lake Charles and Calcasieu, among others. Site-level pages are linked below.
Not exactly. Explosion proof is a broad everyday term; intrinsic safety is one protection concept, which limits energy so ignition cannot occur. Flameproof (Ex d) is a different concept that contains an explosion. The IS-04Z1 is intrinsically safe by design.
Not on its own. US workplace rules accept equipment approved by an OSHA-recognised NRTL and marked accordingly, and ATEX or IECEx certificates are not accepted in their place. Manufacturers usually need a separate US listing, so check the NRTL mark and the Class, Division or Zone marking on any device.
Both exist. Article 500 of the National Electrical Code defines the Class and Division system, and Articles 505 and 506 define Zones. Many existing refineries and gas plants are still classified by Division, so confirm which system the area drawing uses before selecting equipment markings.
IP68 sealing and a rugged build are aimed at August heat and January cold, and the 4,000 mAh battery at a shift away from the truck. The approved ambient range will come from the certificate, which is in progress, so confirm it for both extremes.
Other guides for United States, other places in United States, and the pages behind them.
Tell us what you need to equip and where. The SAMS team answers by email with the datasheet and where each certification route stands.
Send the zone and gas group of your site and we will reply with the datasheet and schedule.