South Africa: industry on the ground
South Africa is the world's largest producer of chrome, manganese, platinum and vanadium and the third-largest coal exporter, so mining is a major source of hazardous-area work.
A Zone 1 / Zone 21 smartphone for crews at the Secunda and Sasolburg complexes, the Natref and Cape Town refineries, Mossel Bay, the fuel terminals and the surface plants of South African mining. Buyers searching for a hazardous area smartphone supplier for South Africa can take the datasheet and the certification schedule for the IS-04Z1 now; supply follows certification.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. A hazardous area smartphone for South Africa cannot be bought yet: the SAMS IS-04Z1 is pre-launch (certification in progress, no certificate issued), and the datasheet, certification schedule and safe-area evaluation units are available now.
Current position: certification in progress, nothing issued, launch targeted for Q4 2026. Operator approval runs on its own timeline. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Zone | 0, 1 or 2 for gas; 20, 21 or 22 for dust | Designed for Zone 1 and Zone 21 |
| Gas group | IIA, IIB or IIC | IIC (target) |
| Area drawing | The operator's own classification drawing | Decided by the site operator |
| Where it applies | South Africa: Durban, Richards Bay, Secunda, Mpumalanga | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in South Africa. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
Operators and classified areas drawn from the SAMS South Africa market guide.
South Africa is the world's largest producer of chrome, manganese, platinum and vanadium and the third-largest coal exporter, so mining is a major source of hazardous-area work.
The code references a family of SANS standards, including SANS 10086 on installation, inspection and maintenance of equipment in explosive atmospheres, SANS 1489 on connectors and SANS 1515 on gas measuring equipment for mines.
ICASA, based in Centurion, sets radio type approval, relying on EU test reports for spectrum, EMC and electrical safety, and a conformity label must be affixed to the equipment and the packaging.
South Africa has a National Code of Practice for Electrical Machinery in Hazardous Locations under the Occupational Health and Safety Act 1993, with a section on regulatory requirements for explosion-protected apparatus.
A hazardous area is a place where flammable gas, vapour or combustible dust may be present. Standards divide these into zones: Zones 0, 1 and 2 for gas and vapour, and Zones 20, 21 and 22 for dust. Zone 1 and Zone 21 are the tier where an explosive atmosphere is likely to occur in normal operation, which is where the IS-04Z1 is designed to work. Anything carried in must be marked for the zone, gas group and temperature class of the area.
No certificate has been issued for the IS-04Z1 yet, so it must not be taken into a classified area until the certificate covering it exists and the site operator has accepted it.
In South Africa. South African classified areas include synthetic fuels and chemicals, coastal refineries and fuel terminals, and the surface plants at coal and mineral operations. The operator classifies each area. Underground mining is equipment Group I and outside the scope of this device. SAMS does not classify any area.
Nothing can be bought for South Africa today: the IS-04Z1 is pre-launch, and SAMS will supply end users through authorised distributors once certificates exist. What a buyer can do now is take the specification, ask for the written certification schedule and arrange a safe-area evaluation, so that the right local channel contacts you at launch.
The technical specification, marking target and conditions of use, sent by email.
Which certificates are in progress, in what order, and what is still to be confirmed.
Evaluation units can be used for connectivity, MDM enrolment and workflow testing outside classified areas.
Tell us the site, zone, gas group and quantity so the right authorised distributor can contact you.
Not today. Until the certificates are issued the IS-04Z1 stays out of classified areas, and until launch there is nothing to purchase. You can ask for the datasheet and the certification schedule, or book a safe-area evaluation unit.
There is no list price yet. SAMS gives indicative pre-launch pricing in writing, against a stated quantity and site, and does not commit to a lead time before certification completes.
Zone 1 and Zone 21 (gas and dust) with gas group IIC and temperature class T4, subject to certification. It must not be used in a classified area before its certificate is issued and the site has accepted it.
The market guide for South Africa covers Secunda, Mpumalanga, Sasolburg, Free State, Milnerton, Cape Town, Mossel Bay, Western Cape, among others. Site-level pages are linked below.
Through authorised distributors once certificates exist. Until then SAMS can send the datasheet and certification schedule and arrange safe-area evaluation units.
ICASA sets radio type approval, and it is described as relying on EU test reports covering spectrum use, EMC and electrical safety, with a conformity label on the equipment and packaging. SABS and NRCS handle some electrical-safety certificates separately. Confirm the route for your device with ICASA or an agent.
Conditions vary from hot, dusty surface sites to deep underground workings with heat and humidity. Check ingress protection, operating temperature range and battery life, and confirm site rules on device approval and gas detection with the mine or plant operator.
IP68 sealing and a rugged build are aimed at hot summers, cold winter mornings and dusty conditions. The approved ambient range will be stated on the certificate, which is in progress. Check that range against the coldest morning shift at your site before ordering.
Related guides for South Africa and for South Africa.
Send the site, zone and gas group and roughly how many handsets. We reply by email with the datasheet and the certification schedule.
Name the site and the operator and we will send what is available before launch.