Japan: rules and approvals
Radio equipment falls under the Telec technical conformity scheme of the communications ministry, and a certified-products database can be searched to check a model.
The IS-04Z1 is an intrinsically safe handset for people who cross into classified areas in Japan every shift: refinery and petrochemical-complex operators, LNG terminal crews, inspection engineers, and the HSE and telecoms teams who equip them. This page explains what to look for in a hazardous area mobile phone for Japan, and where the IS-04Z1 stands against that list today.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. The SAMS IS-04Z1 is the intrinsically safe smartphone covered here for Japan: pre-launch, designed for Zone 1 and Zone 21 (marking target Ex ib IIC T4), with certification in progress and no certificate issued.
Status: pre-launch. IECEx, ATEX, UKEX and NEC 500 certification is in progress and no certificate has been issued; launch is planned for Q4 2026. Operator approval runs on its own timeline. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Zone | 0, 1 or 2 for gas; 20, 21 or 22 for dust | Designed for Zone 1 and Zone 21 |
| Gas group | IIA, IIB or IIC | IIC (target) |
| Area drawing | The operator's own classification drawing | Decided by the site operator |
| Where it applies | Japan: Kashima, Mizushima, Chiba / Sodegaura | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Japan. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
The classified areas, operators and sites below are the ones covered in the SAMS Japan market guide.
Radio equipment falls under the Telec technical conformity scheme of the communications ministry, and a certified-products database can be searched to check a model.
Small rivers, including the Edo River, supply water to the Keiyo industrial region, and the Port of Chiba serves the zone.
Explosion-protected electrical equipment must pass type examination, called kentei, under Article 44-2 of the Industrial Safety and Health Act, and equipment without the pass mark may not be used.
The type examination involves a sample for structural inspection, with no factory audit in law, and the applicant can be a Japanese or foreign manufacturer or an importer.
A hazardous area is a place where flammable gas, vapour or combustible dust may be present. Standards divide these into zones: Zones 0, 1 and 2 for gas and vapour, and Zones 20, 21 and 22 for dust. Zone 1 and Zone 21 are the tier where an explosive atmosphere is likely to occur in normal operation, which is where the IS-04Z1 is designed to work. Anything carried in must be marked for the zone, gas group and temperature class of the area.
No certificate has been issued for the IS-04Z1 yet, so it must not be taken into a classified area until the certificate covering it exists and the site operator has accepted it.
In Japan. Japanese classified areas include refining and petrochemical complexes at Kashima, Mizushima, Chiba and Sodegaura, Yokkaichi and Sakai, plus LNG and thermal power assets. The operator classifies each area, not SAMS. The IS-04Z1 is designed for Zone 1 and Zone 21, in gas and dust areas.
A short checklist for anyone writing or reviewing the specification, with the IS-04Z1 status against each point.
Not yet. The IS-04Z1 is pre-launch and its certification is still in progress ahead of a Q4 2026 launch. No unit goes into a classified area before the certificate covering it exists. The datasheet, the certification schedule and safe-area evaluation units are available now.
SAMS has not published a price. Any figure you are offered for an uncertified Ex phone should be treated with caution; written indicative pricing is available for a defined quantity and site.
Zone 1 and Zone 21 (gas and dust) with gas group IIC and temperature class T4, subject to certification. It must not be used in a classified area before its certificate is issued and the site has accepted it.
The market guide for Japan covers Kashima, Mizushima, Chiba / Sodegaura, Yokkaichi, among others. Site-level pages are linked below.
Not exactly. Explosion proof is a broad everyday term; intrinsic safety is one protection concept, which limits energy so ignition cannot occur. Flameproof (Ex d) is a different concept that contains an explosion. The IS-04Z1 is intrinsically safe by design.
Explosion-protected electrical equipment must pass type examination under Article 44-2 of the Industrial Safety and Health Act, and equipment without the pass mark may not be used. Registered examination bodies, including some outside Japan, carry it out. Check the current process with one of them.
Typically in coastal industrial zones such as the Keiyo zone along Tokyo Bay, which has refineries and chemical plants, and similar bayside complexes elsewhere. The operator issues the area classification, so request the zone drawing, gas group and temperature class before selecting equipment.
The market guide lists TIIS and IECEx as in progress and neither has been granted. Whether a given site needs TIIS depends on the operator and the regulations it follows. Ask the site operator and check the current certification status before ordering.
Related guides for Japan and for Japan.
Tell us what you need to equip and where. The SAMS team answers by email with the datasheet and where each certification route stands.
Tell us the zone, gas group and operator. We will send the datasheet and the certification schedule.