Japan: rules and approvals
Radio equipment falls under the Telec technical conformity scheme of the communications ministry, and a certified-products database can be searched to check a model.
The IS-04Z1 is an intrinsically safe handset for people who cross into classified areas in Japan every shift: refinery and petrochemical-complex operators, LNG terminal crews, inspection engineers, and the HSE and telecoms teams who equip them. This page sets out how a hazardous area cell phone supply route to Japan will work for the IS-04Z1, and what is and is not available before launch.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. A hazardous area cell phone for Japan cannot be bought yet: the SAMS IS-04Z1 is pre-launch (certification in progress, no certificate issued), and the datasheet, certification schedule and safe-area evaluation units are available now.
For the record, no certificate exists for the IS-04Z1 today. The programme is under way ahead of a Q4 2026 launch. An operator's own vendor approval is a separate step. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Zone | 0, 1 or 2 for gas; 20, 21 or 22 for dust | Designed for Zone 1 and Zone 21 |
| Gas group | IIA, IIB or IIC | IIC (target) |
| Area drawing | The operator's own classification drawing | Decided by the site operator |
| Where it applies | Japan: Sakai, Kashima, Mizushima | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Japan. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
The classified areas, operators and sites below are the ones covered in the SAMS Japan market guide.
Radio equipment falls under the Telec technical conformity scheme of the communications ministry, and a certified-products database can be searched to check a model.
Small rivers, including the Edo River, supply water to the Keiyo industrial region, and the Port of Chiba serves the zone.
Explosion-protected electrical equipment must pass type examination, called kentei, under Article 44-2 of the Industrial Safety and Health Act, and equipment without the pass mark may not be used.
The type examination involves a sample for structural inspection, with no factory audit in law, and the applicant can be a Japanese or foreign manufacturer or an importer.
A hazardous area is a place where flammable gas, vapour or combustible dust may be present. Standards divide these into zones: Zones 0, 1 and 2 for gas and vapour, and Zones 20, 21 and 22 for dust. Zone 1 and Zone 21 are the tier where an explosive atmosphere is likely to occur in normal operation, which is where the IS-04Z1 is designed to work. Anything carried in must be marked for the zone, gas group and temperature class of the area.
No certificate has been issued for the IS-04Z1 yet, so it must not be taken into a classified area until the certificate covering it exists and the site operator has accepted it.
In Japan. Japanese classified areas include refining and petrochemical complexes at Kashima, Mizushima, Chiba and Sodegaura, Yokkaichi and Sakai, plus LNG and thermal power assets. The operator classifies each area, not SAMS. The IS-04Z1 is designed for Zone 1 and Zone 21, in gas and dust areas.
Supply of the IS-04Z1 to Japan starts only after certification, through authorised distributors. Until then a buyer can request the datasheet and the written certification schedule, and arrange a safe-area evaluation unit, which puts the site on the list for the right local channel at launch.
The technical specification, marking target and conditions of use, sent by email.
Which certificates are in progress, in what order, and what is still to be confirmed.
Evaluation units can be used for connectivity, MDM enrolment and workflow testing outside classified areas.
Tell us the site, zone, gas group and quantity so the right authorised distributor can contact you.
Not today. Until the certificates are issued the IS-04Z1 stays out of classified areas, and until launch there is nothing to purchase. You can ask for the datasheet and the certification schedule, or book a safe-area evaluation unit.
There is no list price yet. SAMS gives indicative pre-launch pricing in writing, against a stated quantity and site, and does not commit to a lead time before certification completes.
Zone 1 and Zone 21 (gas and dust) with gas group IIC and temperature class T4, subject to certification. It must not be used in a classified area before its certificate is issued and the site has accepted it.
The market guide for Japan covers Kashima, Mizushima, Chiba / Sodegaura, Yokkaichi, among others. Site-level pages are linked below.
Through authorised distributors once certificates exist. Until then SAMS can send the datasheet and certification schedule and arrange safe-area evaluation units.
Explosion-protected electrical equipment must pass type examination under Article 44-2 of the Industrial Safety and Health Act, and equipment without the pass mark may not be used. Registered examination bodies, including some outside Japan, carry it out. Check the current process with one of them.
Typically in coastal industrial zones such as the Keiyo zone along Tokyo Bay, which has refineries and chemical plants, and similar bayside complexes elsewhere. The operator issues the area classification, so request the zone drawing, gas group and temperature class before selecting equipment.
The market guide lists TIIS and IECEx as in progress and neither has been granted. Whether a given site needs TIIS depends on the operator and the regulations it follows. Ask the site operator and check the current certification status before ordering.
Other guides for Japan, other places in Japan, and the pages behind them.
Send the site, zone and gas group and roughly how many handsets. We reply by email with the datasheet and the certification schedule.
Send the zone and gas group of your site and we will reply with the datasheet and schedule.