Japan: rules and approvals
Radio equipment falls under the Telec technical conformity scheme of the communications ministry, and a certified-products database can be searched to check a model.
The IS-04Z1 is an intrinsically safe handset for people who cross into classified areas in Japan every shift: refinery and petrochemical-complex operators, LNG terminal crews, inspection engineers, and the HSE and telecoms teams who equip them. The Keiyo Industrial Zone runs along the north-eastern coast of Tokyo Bay through eight cities in Chiba Prefecture, from Urayasu to Futtsu, including Chiba, Kisarazu and Ichihara. An Ex-proof cell phone distributor in Japan would carry the IS-04Z1 to these buyers once certification completes.
Pre-launch · certification in progress · Launching Q4 2026
Short answer. Japan has no appointed SAMS distributor yet: the IS-04Z1 is pre-launch (certification in progress, no certificate issued, launch planned for Q4 2026), and distributor applications are open.
Where things stand: the IS-04Z1 has not launched, and none of its four certification routes has produced a certificate yet. A buyer's engineering review is separate from the certificate. Certification status. Place facts reviewed October 2026.
| Check | What to look for | IS-04Z1 today |
|---|---|---|
| Ex marking | Group, category, protection concept, gas group, temperature class | II 2 G Ex ib IIC T4 (target) |
| Gas group | IIA, IIB or IIC matched to the area drawing | IIC (target) |
| Temperature class | T-class below the ignition temperature of the gas | T4, 135 °C (target) |
| Where it applies | Japan: Mizushima, Chiba / Sodegaura, Yokkaichi | Classified by the site operator |

An intrinsically safe Android smartphone designed for Zone 1 and Zone 21 hazardous areas in Japan. It is pre-launch: IECEx, ATEX and NEC 500 certification is in progress ahead of the Q4 2026 launch.
Operators and classified areas drawn from the SAMS Japan market guide.
Radio equipment falls under the Telec technical conformity scheme of the communications ministry, and a certified-products database can be searched to check a model.
Small rivers, including the Edo River, supply water to the Keiyo industrial region, and the Port of Chiba serves the zone.
Explosion-protected electrical equipment must pass type examination, called kentei, under Article 44-2 of the Industrial Safety and Health Act, and equipment without the pass mark may not be used.
The type examination involves a sample for structural inspection, with no factory audit in law, and the applicant can be a Japanese or foreign manufacturer or an importer.
“Ex-proof” is shorthand for equipment carrying an explosion-protection marking (the Ex mark) that matches the area it enters. The marking states the protection concept, gas or dust group and temperature class, and it must be backed by a certificate issued by a recognised body, so a phone described as Ex-proof should come with a certificate number you can check.
The IS-04Z1 is designed to carry the marking II 2 G Ex ib IIC T4. That is a target: certification is in progress, no certificate has been issued, and SAMS will publish the certificate numbers when they exist.
In Japan. A Japanese marking check would compare gas group, dust capability, category and temperature class with the complex's zone plan. Refining, petrochemical and LNG areas can differ, so the group needed follows the operator's classification. The IS-04Z1 marking target is II 2 G Ex ib IIC T4, and it is not a granted marking.
SAMS is appointing authorised distributors ahead of the Q4 2026 launch. No territory has been granted for Japan yet and applications are reviewed company by company. Because a certified Ex device cannot be opened by an ordinary phone workshop without invalidating its certificate, SAMS looks for partners who can provide competent technical support and after-sales service locally.
No. Nothing can be bought or taken into a classified area today: certification is in progress and launch is planned for Q4 2026. What is available now is the datasheet, the written certification schedule and evaluation units for safe-area use.
SAMS has not published a price. Any figure you are offered for an uncertified Ex phone should be treated with caution; written indicative pricing is available for a defined quantity and site.
The marking target is II 2 G Ex ib IIC T4. It becomes a marking only when the certificate is issued; until then it is a design target.
The market guide for Japan covers Kashima, Mizushima, Chiba / Sodegaura, Yokkaichi, among others. Site-level pages are linked below.
Apply through the distributor page with your company details and the territory you cover. SAMS reviews applications company by company and has not yet granted a territory for Japan.
Explosion-protected electrical equipment must pass type examination under Article 44-2 of the Industrial Safety and Health Act, and equipment without the pass mark may not be used. Registered examination bodies, including some outside Japan, carry it out. Check the current process with one of them.
Typically in coastal industrial zones such as the Keiyo zone along Tokyo Bay, which has refineries and chemical plants, and similar bayside complexes elsewhere. The operator issues the area classification, so request the zone drawing, gas group and temperature class before selecting equipment.
The market guide lists TIIS and IECEx as in progress and neither has been granted. Whether a given site needs TIIS depends on the operator and the regulations it follows. Ask the site operator and check the current certification status before ordering.
Other guides for Japan, other places in Japan, and the pages behind them.
Share the site details and quantity. You will get the datasheet and the certification schedule back by email; pricing is indicative only until launch.
Name the site and the operator and we will send what is available before launch.